Emetteur / récepteur WISYCOM BUNDLE MCR42 + MTP41S/40S

WISYCOM

VHFWISBUNDLEMTP41

Ce produit n'est plus en stock

6 250,00 €

HT

Pack "Bundle" composé de : 1 MCR 42, 2 MPT 41S.

Plus de détails

Pack "Bundle" wisycom :

"Bundle CINEMA" composé de :

- 1 MCR 42 Plan N (470-700Mhz)
- 1 BPA42-BGcon2
- 2 MTP 41S Plan B1 (470-640Mhz)
- 2 CAL-120

Émetteurs :  MPT41S

Principales caractéristiques :

  • Ecran LCD (128 x 32 pixels)
  • Limiter HW (S)
  • 232 MHz de largeur de bande entre 470 et 798 MHz.
  • Coque en métal "Ultra-light" (60g sans batterie)
  • Système de compendeur sélectionnable :
        ENR (noise optimized)
        ENC (voice optimized)
  • Battery: 1 AA Alkaline, rechargeable NiMH or Lithium
  • Autonomie: > 5h @ 50mW de puissance. > 7h @ 10mW de puissance
  • Système infrarouge pour la sélection de fréquence + firmware
  • Niveau d'entrée max 26dBu (15.5 V clip).

Émetteurs :  MPT40S

Principales caractéristiques :

  • Ecran LCD (128 x 32 pixels)
  • Limiter HW (S)
  • 232 MHz de largeur de bande entre 470 et 798 MHz.
  • Coque en métal "Ultra-light" (60g sans batterie)
  • Système de compendeur sélectionnable :
        ENR (noise optimized)
        ENC (voice optimized)
  • Battery: 2 AA Alkaline, rechargeable NiMH or Lithium
  • Autonomie: > 10h @ 50mW de puissance. > 14h @ 10mW de puissance
  • Système infrarouge pour la sélection de fréquence + firmware
  • Niveau d'entrée max 26dBu (15.5 V clip).
  • 48V phantom power pour micro à condensateur en utilisant l’accessoire  PHA48.

Récepteur : MCR42S

Le MCR42 de Wisycom est un double récepteur portable large bande , pouvant directement s'adapter sur certaines caméras (Panasonic, Sony, Grass Valley) avec le slot adapté.C'est un vrai double diversity . La manipulation est très intuitive. Le MCR42 dispose d'un scanner intégré. Le MCR 42 permet aussi de recevoir les émetteurs Audio Limited TX 2000-2040 , la série SK, la série Evolution G2 G3 de Sennheiser.

Principales caractéristiques :

  • Bande passante : 232 MHz.
  • 1 choix de BP : MCR-N.
  • 40 groupes de 60 fréquences préprogrammées par pas de 25KHz.
  • Fréquences programmables par nos soins
  • Sorties : RX 1 et RX 2 en TA3/M / Analogique ou AES.
  • Niveau sorties : réglable par pas de 1 db de -20db à + 6 dbu (nominal).
  • Alimentation : EXT : connecteur Hirose / INT : Kit pack batterie BCA 42 : 5* LR06.
  • Dimensions : (H x L x P) : 6,8 cm x 1,8 cm x 13.5 cm Poids : 180 gr

Slot : BPA 42 HPN

  • 2 output mini XLR-3pin male (2 main analogue audio channel ou 2 digital AES)
  • 1 output jack Stereo 3.5mm(TRS)
  • 1 power connector Hirose.

Slot : BPA 42 PTT

  • 2 output mini XLR-3pin male (2 main analogue audio channel ou 2 digital AES)
  • 1 output jack Stereo 3.5mm(TRS)
  • 1 power connector Hirose.
  • 1 output mini XLR-5pin (2 auxiliary audio output from push to talk function)

2 CAL / 120

2 câble Mini XLR-3pin male / XLR-3pin male de 120cm

Aucun avis n'a été publié pour le moment.

Donnez votre avis

SENNHEISER EW 112 P

Système d’émetteur / récepteur HF avec micro omnidirectionnel.

- WISYCOM MCR42S :

Frequency rangesN band   470 ÷ 700 MHz
M band   566 ÷ 798 MHz
Extended limits or other custom ranges are available on request
Switchable channels40 groups of 60 channels fully user progr
Switching-windowup 240 MHz
Frequenciesmicroprocessor controlled frequency synthesizer circuit, with 25 kHz minimum step. The frequencies is easily PC reprogrammed with the optional UPK 300E Programming Kit
Frequency error< ± 2.5 ppm, in the rated temperature range
Temperature range-10 ÷ +55 °C
ModulationFM, with 50 μs de-emphasis
Nominal deviation±40 kHz (Max. operating dev. = ± 60 kHz)
“A” / “B” antenna inputswith sturdy connectors
Antenna input impedance50 ohm sma type (SWR < 1:2; typ. 1:1.4)
Sensitivity2 μV ( 0 dBμV), for SND/N > 58 dB
5 μV (14 dBμV), for SND/N > 98 dB
in the whole switching-window [*]
Amplitude response< 0.5 dB (RF input sig.:6 dBμV ÷ 100 dBμV)
Co-channel rejection> 2.5 dB
Adjacent chan. selectivity> 80 dB typical (for ch. spacing ≥ 400 kHz)
Spurious rec. rejection> 100 dB
IF image rejection> 90 dB
Intermod. rejection> 76 dB
IIP3> +10 dBm typical
Spurious emissions< 2 nW (typical = 0.1 pW)
Noise Reduction systemENR (Wisycom Extended-NR), noise optimized
ENC (Wisycom Extended-NC), voice optimized & with reduced pre-emphasys
Others, compatible with most systems, thru an internal DSP emulation of SA572, SA575 and Rms envelope compander chip set, fully user programmable
AF bandwidth30 Hz ÷ 20 kHz
Frequency response± 0.5 dB in the 30 Hz ÷ 19 kHz range
Distortion• MCR42S: 0.3 % typical • MCR42S2: 0.1 % typical
SND/D ratio (Analogue)110 dB typical [*]
SND/D ratio (AES3)• MCR42S: >125 dB typical [*] • MCR42S2: >140 dB typical [*]
POWER LEDs
(OLD display, discontinued)
2 multicolor RGB LEDs to easy indicate Rx1 & Rx2 power status:
GREEN, if "Receiver ON" with external power supply;
RED, if Empty battery/power supply;
LEDs blinking indicates power supply status of transmitter:
    - slow blinking, at 25% battery capacity;
    - fast blinking, at 12.5% battery capacity.
POWER LEDs
(NEW display)
1 multicolour RGB LEDs to easy indicate Rx1 & Rx2 power status:
GREEN/PALE GREEN if "Receivers ON" with external power supply/battery;
GREEN blinking/PALE GREEN blinking if low power supply/ low battery level
RED blinking indicates power supply status of transmitter:
    - slow blinking, at 25% battery capacity;
    - fast blinking, at 12.5% battery capacity.
RF LEDs2 multicolor RGB LEDs to easy indicates Rx1 & Rx2 RF status. Always on in normal operation:
RED, if both receivers RF level is under squelch level;
GREEN, if signal above squelch level & antenna A (green) is active;
BLUE, if signal above squelch level & antenna B (blue) is active;
YELLOW, if signal above squelch and both antenna are used.
AUDIO LEDs2 multicolor RGB LEDs to easy indicates Rx1 & Rx2 audio status:
RED, if audio is muted cause of squelch (or tone squelch if active)
GREEN, if audio is active and tone squelch present
BLUE, if audio is active and tone squelch not present
Front buttonssimple operation with 4 buttons to quickly monitor and setup the receiver
One touch function for a frequency scan and sync function
PoweringExternal = 5 ÷ 18 Vdc (1.5 W max)
Autonomous. = with optional BCA 42 Battery Module (5 x IEC-LR6 1.5V size-AA alkaline or rechargeable elements)
Dimensions“Slot-in” execution= 68 x 18 x 115 mm, “Stand-alone” exec. = 68 x 18 x 135 mm
Weight180 g approx.
Analogue Audio Output• Audio line-output electronically balanced on two 3 pin mini-XLR Female connector
• Audio line-output level Adjustable in a one dB step between: -30/-18 (depending on the HW vers.) and +6 dBu (nominal) and MAX +12 dBu (peak deviation)
• Audio line-output imped. ≤ 200 ohm
Push to Talk (PTT) Audio Outputelectronically balanced on a 5 pin mini-XLR Male connector
Digital Audio Output• electronically balanced on 3 pin mini-XLR Male connector
• AES3 @ 48 kHz

[*] RMS value, 22 Hz / 22 kHz, unweighted

- WISYCOM MTP41S :

Switchable channels2400 allocated by 40 groups of 60 channels (in specific frequency range), quickly selectable with dedicated buttons
Switching windowUp to 232 MHz, depending on band
1 470 ÷ 640 MHz
2 566 ÷ 798 MHz
3 510 ÷ 698 MHz
FrequenciesQuartz PLL frequency synthesizer circuit (25 kHz step)
Frequency stability± 2,5 ppm (in the rated temperature range)
Temperature range-10 ÷ +55 °C
Max RF power50 mW (ERP) when high power selected
10 mW (ERP) when low power selected
Spurious emissions< 2 nW
Modulationwideband FM, with 50 µs pre-emphasis
Nominal deviation±40 kHz (Peak deviation = ±56 kHz)
Telemetry featureMTP41 transmits also a digitally modulated sub-carrier, suitable for: tone-squelch operating remote battery monitoring optional PTT (push to talk) operation
AF input connector LEMO optionConfigurable on ‘mic’ display menu in 3 options:
’2 wires’: gain selectable -40 ÷ +40 (-54 dBu ÷ +26 dBu peak), no bias voltage
‘2 wires + bias’: gain selectable -20 ÷ +40 (-54 dBu ÷ + 6 dBu peak), 5.5 V on 4k7 bias supply
‘3 wires: gain selectable -40 ÷ +40 (-54 dBu ÷ +26 dBu peak)
AF input level :
80 dB adjustable range from -60 dBu (775 uV) to 26 dBu (15.5 V) at peak deviation (1 kHz), adjustable in 1 dB steps
Max. input level+26 dBu (15.5 V) at clipping, +20 dBu (7.75 V) at nominal level
Noise-ReductionENR (Wisycom Extended-NR), with independent Attack- and Recovery-time, noise optimized
ENC (Wisycom Extended-NC), with independent Attack- and Recovery-time, voice optimized & with reduced pre-emphasys
AF bandwidth45 Hz ÷ 21 KHz (3dB)
55 Hz ÷ 20 KHz (1dB)
Distortion< 0.3 % (0.15 % typ.)
Signal-to-noise ratiotyp. 115 dB (A)rms with 40 kHz deviation
typ. 121 dB (A)rms with 56 kHz deviation
LedLed indication with bicolor led (red & green) on wireless power switch:
Wireless transmission status: GREEN on/off
Modulation peek (if activated): RED
Battery lifetime status: GREEN - steady (> 25%) - slowly blinking (< 25%) - quickly blinking (<12%)
Ptt status: RED if active
DisplayHigh contrast OLED (Organic light-emitting diode) bicolor display (96 x 36 pixels)
8 step battery lifetime indication: 7 bars (100%-87%-75%-63-50%-38%-25%) and “empty bar” quickly blinking (12% remaining)
PTT functionPin 3 of the AF connector can be setup to an external push button
Power supply1 AA size batteries (Alkaline, rechargeable NiMH)
Battery lifeapprox. 5 hours @ 50mW continuous working
approx. 7 hours @ 10mW continuous working
WeightApprox. 75 g. without batteries

- WISYCOM MCR42S :

Frequency rangesN band   470 ÷ 700 MHz
M band   566 ÷ 798 MHz
Extended limits or other custom ranges are available on request
Switchable channels40 groups of 60 channels fully user progr
Switching-windowup 240 MHz
Frequenciesmicroprocessor controlled frequency synthesizer circuit, with 25 kHz minimum step. The frequencies is easily PC reprogrammed with the optional UPK 300E Programming Kit
Frequency error< ± 2.5 ppm, in the rated temperature range
Temperature range-10 ÷ +55 °C
ModulationFM, with 50 μs de-emphasis
Nominal deviation±40 kHz (Max. operating dev. = ± 60 kHz)
“A” / “B” antenna inputswith sturdy connectors
Antenna input impedance50 ohm sma type (SWR < 1:2; typ. 1:1.4)
Sensitivity2 μV ( 0 dBμV), for SND/N > 58 dB
5 μV (14 dBμV), for SND/N > 98 dB
in the whole switching-window [*]
Amplitude response< 0.5 dB (RF input sig.:6 dBμV ÷ 100 dBμV)
Co-channel rejection> 2.5 dB
Adjacent chan. selectivity> 80 dB typical (for ch. spacing ≥ 400 kHz)
Spurious rec. rejection> 100 dB
IF image rejection> 90 dB
Intermod. rejection> 76 dB
IIP3> +10 dBm typical
Spurious emissions< 2 nW (typical = 0.1 pW)
Noise Reduction systemENR (Wisycom Extended-NR), noise optimized
ENC (Wisycom Extended-NC), voice optimized & with reduced pre-emphasys
Others, compatible with most systems, thru an internal DSP emulation of SA572, SA575 and Rms envelope compander chip set, fully user programmable
AF bandwidth30 Hz ÷ 20 kHz
Frequency response± 0.5 dB in the 30 Hz ÷ 19 kHz range
Distortion• MCR42S: 0.3 % typical • MCR42S2: 0.1 % typical
SND/D ratio (Analogue)110 dB typical [*]
SND/D ratio (AES3)• MCR42S: >125 dB typical [*] • MCR42S2: >140 dB typical [*]
POWER LEDs
(OLD display, discontinued)
2 multicolor RGB LEDs to easy indicate Rx1 & Rx2 power status:
GREEN, if "Receiver ON" with external power supply;
RED, if Empty battery/power supply;
LEDs blinking indicates power supply status of transmitter:
    - slow blinking, at 25% battery capacity;
    - fast blinking, at 12.5% battery capacity.
POWER LEDs
(NEW display)
1 multicolour RGB LEDs to easy indicate Rx1 & Rx2 power status:
GREEN/PALE GREEN if "Receivers ON" with external power supply/battery;
GREEN blinking/PALE GREEN blinking if low power supply/ low battery level
RED blinking indicates power supply status of transmitter:
    - slow blinking, at 25% battery capacity;
    - fast blinking, at 12.5% battery capacity.
RF LEDs2 multicolor RGB LEDs to easy indicates Rx1 & Rx2 RF status. Always on in normal operation:
RED, if both receivers RF level is under squelch level;
GREEN, if signal above squelch level & antenna A (green) is active;
BLUE, if signal above squelch level & antenna B (blue) is active;
YELLOW, if signal above squelch and both antenna are used.
AUDIO LEDs2 multicolor RGB LEDs to easy indicates Rx1 & Rx2 audio status:
RED, if audio is muted cause of squelch (or tone squelch if active)
GREEN, if audio is active and tone squelch present
BLUE, if audio is active and tone squelch not present
Front buttonssimple operation with 4 buttons to quickly monitor and setup the receiver
One touch function for a frequency scan and sync function
PoweringExternal = 5 ÷ 18 Vdc (1.5 W max)
Autonomous. = with optional BCA 42 Battery Module (5 x IEC-LR6 1.5V size-AA alkaline or rechargeable elements)
Dimensions“Slot-in” execution= 68 x 18 x 115 mm, “Stand-alone” exec. = 68 x 18 x 135 mm
Weight180 g approx.
Analogue Audio Output• Audio line-output electronically balanced on two 3 pin mini-XLR Female connector
• Audio line-output level Adjustable in a one dB step between: -30/-18 (depending on the HW vers.) and +6 dBu (nominal) and MAX +12 dBu (peak deviation)
• Audio line-output imped. ≤ 200 ohm
Push to Talk (PTT) Audio Outputelectronically balanced on a 5 pin mini-XLR Male connector
Digital Audio Output• electronically balanced on 3 pin mini-XLR Male connector
• AES3 @ 48 kHz

[*] RMS value, 22 Hz / 22 kHz, unweighted

- WISYCOM MTP41S :

Switchable channels2400 allocated by 40 groups of 60 channels (in specific frequency range), quickly selectable with dedicated buttons
Switching windowUp to 232 MHz, depending on band
1 470 ÷ 640 MHz
2 566 ÷ 798 MHz
3 510 ÷ 698 MHz
FrequenciesQuartz PLL frequency synthesizer circuit (25 kHz step)
Frequency stability± 2,5 ppm (in the rated temperature range)
Temperature range-10 ÷ +55 °C
Max RF power50 mW (ERP) when high power selected
10 mW (ERP) when low power selected
Spurious emissions< 2 nW
Modulationwideband FM, with 50 µs pre-emphasis
Nominal deviation±40 kHz (Peak deviation = ±56 kHz)
Telemetry featureMTP41 transmits also a digitally modulated sub-carrier, suitable for: tone-squelch operating remote battery monitoring optional PTT (push to talk) operation
AF input connector LEMO optionConfigurable on ‘mic’ display menu in 3 options:
’2 wires’: gain selectable -40 ÷ +40 (-54 dBu ÷ +26 dBu peak), no bias voltage
‘2 wires + bias’: gain selectable -20 ÷ +40 (-54 dBu ÷ + 6 dBu peak), 5.5 V on 4k7 bias supply
‘3 wires: gain selectable -40 ÷ +40 (-54 dBu ÷ +26 dBu peak)
AF input level :
80 dB adjustable range from -60 dBu (775 uV) to 26 dBu (15.5 V) at peak deviation (1 kHz), adjustable in 1 dB steps
Max. input level+26 dBu (15.5 V) at clipping, +20 dBu (7.75 V) at nominal level
Noise-ReductionENR (Wisycom Extended-NR), with independent Attack- and Recovery-time, noise optimized
ENC (Wisycom Extended-NC), with independent Attack- and Recovery-time, voice optimized & with reduced pre-emphasys
AF bandwidth45 Hz ÷ 21 KHz (3dB)
55 Hz ÷ 20 KHz (1dB)
Distortion< 0.3 % (0.15 % typ.)
Signal-to-noise ratiotyp. 115 dB (A)rms with 40 kHz deviation
typ. 121 dB (A)rms with 56 kHz deviation
LedLed indication with bicolor led (red & green) on wireless power switch:
Wireless transmission status: GREEN on/off
Modulation peek (if activated): RED
Battery lifetime status: GREEN - steady (> 25%) - slowly blinking (< 25%) - quickly blinking (<12%)
Ptt status: RED if active
DisplayHigh contrast OLED (Organic light-emitting diode) bicolor display (96 x 36 pixels)
8 step battery lifetime indication: 7 bars (100%-87%-75%-63-50%-38%-25%) and “empty bar” quickly blinking (12% remaining)
PTT functionPin 3 of the AF connector can be setup to an external push button
Power supply1 AA size batteries (Alkaline, rechargeable NiMH)
Battery lifeapprox. 5 hours @ 50mW continuous working
approx. 7 hours @ 10mW continuous working
WeightApprox. 75 g. without batteries
J'accepte

Si vous acceptez que le site A4Audio utilise les cookies pour faciliter votre navigation cliquez sur "J'accepte"